Zu Inhalt springen
€100 = KOSTENLOSER VERSAND
€100 = KOSTENLOSER VERSAND

Full custom | Zero+

Sparen Sie 12 %
Ursprünglicher Preis €1.199,00
Aktueller Preis €1.050,00

Kostenloser Versand (ab €100,-)!
30 Tage Bedenkzeit
Ratschläge von Experten

Benachrichtigen Sie mich, wenn der Artikel wieder verfügbar ist

Wenn du deine Leistung bei Zeitfahren und Triathlons verbessern möchtest – suche nicht weiter!

Der Zero+ ist der schnellste Schuh im Bont Cycling-Sortiment.

Kein Wunder also, dass Spitzensportler wie Jan Frodeno (Ironman-Weltmeister) seit vielen Jahren mit dem Zero+ Rekorde brechen.

Dieser Schuh verschwendet dank seiner einzigartigen aerodynamischen Beschichtung und einem zentral angeordneten BOA-Zifferblatt einfach kein Watt.

Eine wichtige Tatsache ist, dass das anatomische Design durch mehr als 20.000 Fußscans unterstützt wird und aus Materialien wie 100 % Carbon besteht, um sicherzustellen, dass diese Schuhe viele Jahre verwendet werden können.

Sobald du in diese Schuhe steigst, wirst du wissen, worum es geht. Und das Beste daran ist, dass du von der ersten bis zur letzten Fahrt so steif, leicht und stark sind.

Warum benötigst du möglicherweise ein Full-Custom-Paar:

  • Ein Fuß ist länger als der andere.
  • Breite Füße.
  • Unregelmäßige Füße.
  • You suffer from hammer and/or claw toes.
  • Unterschied linker/rechter Fuß.
  • Sie haben gerne Ihr eigenes Design.

Was du anpassen könntest:

  • Farben und Design
  • Namensstickerei
  • BOA-Farben

2 ways to get your full-custom pair:

  • Eine Bestellung aufgeben and the team will be in touch to confirm your specific requirements and proceed with the full customization.
  • Kontaktiere uns for any questions and requirements in order to proceed to full customization.

Advantages:

  • Leichter: mit nur 230 Gramm kannst du deine Wattzahl erhöhen.
  • Stärker: dieser steife Schuh besteht aus einem kompletten Karbonchassis, was zu einer höheren Kraftübertragung führt.
  • Schneller: genopptes Durolite-Obermaterial für verbesserte Aerodynamik.
  • Vollständig hitzeverformbar: bei Bedarf kannst du deine Passform durch Hitzeverformung des Schuhs anpassen..

  • Unidirectional 100% Carbon Chassis.
  • Stack height: 3.6mm.
  • Air Vents: frontal area air vents and air grills in arch area.
  • Innersole: EVA thermo-moldable.
  • Sole Guards: replaceable.
  • Padding: memory foam.
  • Fit customisation: fully heat moldable chassis.
  • Cleat Mounting: MM grid plus grip / 3 Hole Look Configuration.
  • Closure System: dual Dial Retention System with Kevlar wiring.
  • Weight: 230 grams.
  • Semi and Full Custom available through custom programm.
  • BOA Li2 dial with  The Boa Guarantee, for the life of your shoes.

  • After placing the order or contacting us regarding your semi-custom request, a Bont specialist from the Reins.cc team will contact you.
  • Production lead times are currently 7-8 weeks following confirmation of selections. Please allow additional time for delivery to your chosen address.
  • Reins.cc prioritizes DPD for shipping across Europe. Although it may use a local carrier if appropriate.
  • We provide a track & trace number for you.

First of all, you do not need to mold your shoes if they fit you straight out of the box!
This cycling shoe is the most heat moldable shoe on the market today. Bont’s resin is developed in house and has been perfected over 36 years to be an extremely stiff resin that becomes pliable at relatively low temperatures. The base of the shoe is moldable which means all stiff areas of the shoe can be molded in a standard oven. To mold your shoes, remove any cleats, laces or cleat mounting screws and innersole before molding. Failure to remove the innersole can result in it becoming deformed by the heat. Pre heat the oven to 70°C. Place the shoe in the oven for 20 minutes. Higher temperatures will void your warranty and may damage your boot. Caution: Do not place your feet in the hot shoes or you may burn your feet. Let them cool a little and test the shoe temperature with your hand before placing your feet in the shoes. Tighten the straps and allow to cool. If you have any lumps or bunions on your feet or if there are any areas causing discomfort, while the shoe is hot you can use the round end of a screwdriver to press out any part of the boot. You can heat mold the shoes as many times as you like.

  • Unidirectional 100% Carbon Chassis.
  • Stack height: 3.6mm.
  • Air Vents: frontal area air vents and air grills in arch area.
  • Innersole: EVA thermo-moldable.
  • Sole Guards: replaceable.
  • Padding: memory foam.
  • Fit customisation: fully heat moldable chassis.
  • Cleat Mounting: MM grid plus grip / 3 Hole Look Configuration.
  • Closure System: dual Dial Retention System with Kevlar wiring.
  • Weight: 230 grams.
  • Semi and Full Custom available through custom programm.
  • BOA Li2 dial with  The Boa Guarantee, for the life of your shoes.

  • After placing the order or contacting us regarding your semi-custom request, a Bont specialist from the Reins.cc team will contact you.
  • Production lead times are currently 7-8 weeks following confirmation of selections. Please allow additional time for delivery to your chosen address.
  • Reins.cc prioritizes DPD for shipping across Europe. Although it may use a local carrier if appropriate.
  • We provide a track & trace number for you.

First of all, you do not need to mold your shoes if they fit you straight out of the box!
This cycling shoe is the most heat moldable shoe on the market today. Bont’s resin is developed in house and has been perfected over 36 years to be an extremely stiff resin that becomes pliable at relatively low temperatures. The base of the shoe is moldable which means all stiff areas of the shoe can be molded in a standard oven. To mold your shoes, remove any cleats, laces or cleat mounting screws and innersole before molding. Failure to remove the innersole can result in it becoming deformed by the heat. Pre heat the oven to 70°C. Place the shoe in the oven for 20 minutes. Higher temperatures will void your warranty and may damage your boot. Caution: Do not place your feet in the hot shoes or you may burn your feet. Let them cool a little and test the shoe temperature with your hand before placing your feet in the shoes. Tighten the straps and allow to cool. If you have any lumps or bunions on your feet or if there are any areas causing discomfort, while the shoe is hot you can use the round end of a screwdriver to press out any part of the boot. You can heat mold the shoes as many times as you like.

our store

Not around the corner? We bring the physical shop experience online!